1) Electric current.
2) Drift velocity, relaxation time and mobility.
3) Relation between drift velocity and electric current.
4) Ohm’s law.
5) Conductance.
6) Resistivity and conductivity.
7) Effect of temperature on resistance and resistivity.
8) Colour code for carbon resistors.
9) Combination of resistances.
10) E.M.F. and terminal potential differences of a cell.
11) Grouping of cells.
12) Superconductivity : thermistors and non-ohmic conductors.
2) Drift velocity, relaxation time and mobility.
3) Relation between drift velocity and electric current.
4) Ohm’s law.
5) Conductance.
6) Resistivity and conductivity.
7) Effect of temperature on resistance and resistivity.
8) Colour code for carbon resistors.
9) Combination of resistances.
10) E.M.F. and terminal potential differences of a cell.
11) Grouping of cells.
12) Superconductivity : thermistors and non-ohmic conductors.
Electric currentRate of flow of charge is called electric currentInstantaneous value of current is given by When charge flows at constant rate S.I. unit of electric current is ampere (A). Conventionally, the direction of flow of positive charge is taken as the direction of current. Drift velocity, relaxation time and mobilityDrift velocity is defined as the average velocity with which free electron gets drifted in a direction opposite to the direction of the applied electron field.where, m is mass of the electron E is applied electric field τ is relaxation time. Time interval between two successive collisions is called relaxation time and distance covered during this time is called free path. For a large number of collisions Relaxation time Mobility of a charged particle is its drift velocity per unit electric field. Relation between drift velocity and electric currentI = vdenA where n is no. density of free electrons.A is area of cross-section of the conductor. Ohm’s law“Current flowing through a conductor is directly proportional to the potential difference across the ends of the conductor, provided physical conditions of the conductor (temperat, mechanical strain etc.) are kept constant.”i) nature of the material. ii) dimensions of the material. iii) temperature of the material Oquantitatively. R is called resistance of the conductor S.I.unit of resistance of Ohm (Ω) . |
Conductance (G)Inverse of resistance is called conductanceResistivity and conductivityS.I. unit of resistivity is ohm-metre (Ω m). Conductivity is inverse of resistivity . Effect of temperature on resistance and resistivitywhere ar ia called temperature coefficient of resistivity. Colour code for carbon resistorsToken resistor color coding system applies to carbon film, metal oxide film, fusible, precision metal film, and wirewound (cylindrical with enlarged ends) of the axial lead type. This system is employed for resistors when the surface area is not sufficient to print the resistance value for the past time. At present, Token resistor color coding system is applying for automatization. The first three bands closest to one end of the resistor are used to determine the resistance. The fourth band represents the tolerance of the resistor. Additional information can be obtained from the first band. Generally, If an additional fifth band is black, the resistor is wirewound resistor. If an additional fifth band is white, the resistor is fusible resistor. If only one black band in the center, the resistor is called zero ohm resistor. The colors of the first two bands represent the numerical value of the resistor. The third band represents the power-of-10 multiplier.Colour bands are marked on the body of a carbon resistor to mark its resistance (in ohm) and tolerance (maximum variation in its coded value in %) in accordance with the following code : |
Combination of resistancesResistors are often connected together in a circuit, so it is necessary to know how to determine the resistance of a combination of two or more resistors. There are two basic ways in which resistors can be connected: in series and in parallel. A simple series resistance circuit is shown in Figure 4.4. |
Resistors in SeriesDetermining the total resistance for two or more resistors in series is very simple. Total resistance equals the sum of the individual resistances. In this case, RT=R1+R2 . This makes common sense; if you think again in terms of water flow, a series of obstructions in a pipe add up to slow the flow more than any one. The resistance of a series combination is always greater than any of the individual resistors. |
Resistors in ParrallelThe other method of connecting resistors is shown in Figure 4.5, which shows a simple parallel resistance circuit.Our water pipe analogy indicates that it should be easier for current to flow through this multiplicity of paths, even easier than it would be to flow through any single path. Thus, we expect a parallel combination of resistors to have less resistance than any one of the resistors. Some of the total current will flow through R1 and some will flow through R2, causing an equal voltage drop across each resistor. More current, however, will flow through the path of least resistance. The formula for total resistance in a parallel circuit is more complex than for a series circuit: RT={1{1R1}+{1R2}...+{1Rn}} (1) Parallel and series circuits can be combined to make more complex structures, but the resulting complex resistor circuits can be broken down and analyzed in terms of simple series or parallel circuits. Why would you want to use such combinations? There are several reasons; you might use a combination to get a value of resistance that you needed but did not have in a single resistor. Resistors have a maximum voltage rating, so a series of resistors might be used across a high voltage. Also, several low power resistors can be combined to handle higher power. What type of connection would you use? |
E.M.F. and terminal potential differences of a cellE.M.F. of a cell is the energy spent by a cell on a unit positive charge to make it complete a given electric circuit. E.M.F. of a cell is defined as the potential difference between its terminals in an open circuit .S.I. unit of E.M.F. is volt. Terminal potential difference is defined as the potential difference between the terminals of the cell in a closed circuit. S.I. unit of terminal potential difference is volt. a) Every cell has a charecteristic e.m.f. E and some internal resistance r. when some current I is drawn from the cell, its terminal potential difference is measured to be V where V = E – Ir. From here it follows that V = E when I=0. Thus the e.m.f. of a cell is its terminal potential difference when no current is being drawn from the cell. b) When a current I is forced into a cell of e.m.f. E and internal resistance r, the terminal potential difference is given as V = E + Ir. |
Grouping of cellsa)Series combination of n identical cells of e.m.f. E and internal resistance r each is equivalent to a total e.m.f. of nE and a total internal resistance of nr.b)Parallel combination os n identical cells of e.m.f. E and internal resistance r each is equivalent to a total (net) e.m.f. of E only and total (net) internal resistance of r/n. c)When there are n rows of cells each containing m identical cells of e.m.f. E and internal resistance r each, the net e.m.f. of the combination is mE and the internal resistance of the combination is d)When there are two cells of e.m.f. E1 and E2 and internal resistance r1 and r2 respectively, connected in parallel as shown in fig-d, the net e.m.f. of the combination is e) Cells are connected in series if i) it’s desired to obtain maximum current. ii) external resistance is large. f) Cells are connected in parallel if i) it’s desired to obtain maximum current. ii) external resistance is very low. |
Electrical measurements1. Kirchhoff’s laws.2. Wheatstone Bridge. 3. Metre Bridge. 4. Potential Gradient. 5. Potentiometer and its applications. Kirchhoff’s LawsFirst Law : The algebric sum of currents at a junction is zero, i.e.,ΣI=0. This implies that total current entering a junction is equal to total current leaving the junction.Second Laws : In a close loop, the algebric sum of the e.m.f.’s is equal to the algebric sum of the products of the resistances and the respective currents in them, i.e., ΣE = ΣIR Wheatstone BridgeWheatstone Bridge is a network of four resistors P, Q, R and S connected as shown in fig below. When some potential difference is applied between A and C, the potential difference beween B and D depends only on the ratiohe potential difference between B and D becomes zero and the Wheatstone Bridge is said to be balanced. When B will be at a lower potential w.r.t. D and current will flow from D to B. When B will be at a higher potential w.r.t. D and current will flow from B to D. |
Metre BridgeIt works on the pricipal of Wheatstone bridge. It is so called because it uses a wire which is a metre long. The wire is made of uniform cross-section of a material with a high resistivity and low teemperature coefficient of resistance (e.g. manganin). The fig. 14.4 shows a simple from a Metre Bridge. The wire is streched along a metre scale between two brass or copper strips. The unknown resistance X and a known resistance R (resistance box) are connected between the gaps DF and HK, respectively. When the sliding contact (jockey) is at the position C, it divides the wire into two parts of resistance RAC and RCB ; these resistance with X and R form a Wheatstone bridge.Since the wire is uniform, therefore, RAC and RCB are proportional to I1 and I2 respectively.Thus, Few Important points regarding setup:- The Balance-point is obtaained by trial and error-not by scraping the jockey along the wire.The value of R in the resistance box should be chosen so that the balance pint comes near to the centre of the wire, i.e. from 40 cm to 60 cm from the end A.This is because if either I1 or I2 is small, then the resistance of its end connections AA\ and BB\ will not be negligible in comparison with RAB and RCB . Hence the equation above count hold. |
Potential GradientWhen a steady current is passed in a conductor of uniform cross-section, then the potential difference V across any length ‘l’ i.e.,VaI V = KI is called potential gradient. Potentiometer and its applicationsPotentiometer is an arrangement of a long wire of uniform cross-section and composition.Generally it either has a 4 m long wire or a 10 m long wire. Principle: When there is a constant current in a wire of uniform cross-section and composition, the fall of potential along any length of the wire is directly proportional to the length i.e., VaI. Applications: Comparison of e.m.f.’s of two primary cells can be done with the help of the circuit shown below. If I1 and I2 are the balancing lengths obtained for the cells of e.m.f. E1 and E2 respectively for the same potential gradient along the potentiometer wire, then |
No comments:
Post a Comment