Monday, 16 September 2013

Magnetic Effects of Current, Magnetism

Magnetic effects of current


A) Magnetic Field due to Electric Current.
B) Motion of charged particles in electric and magnetic fields.

A) Magnetic Field due to Electric Current

1. Oersted’s experiment.
2. Magnetic field.
3. Magnetic flux.
4. Biot-Savart law.
5. Ampere’s circuital laws.

Oersted’s experiment

In 1820, Oersted discovered that a magnetic needle gets deflected by a current carrying wire. This experiment confirmed the existence of magnetic field around the current carrying wire.

Magnetic field

Magnetic field is the space around a magnet/current carrying conductor where magnetic influence can be experienced.

Charge can produce a magnetic field only when it is in motion and magnetic field can interact only with a moving charge.

Quantitatively,
This is also called magnetic Lorentz force. Its direction can be determined by :
Fleming’s left hand rule. Magnetic field is also called magnetic induction or magnetic flux density. S.I. unit of  is tesla (T).
Also 10-4 tesla = 1 gauss.

Magnetic flux

Qualitative definition

Total number of magnetic lines of force passing normally through a given area is called magnetic flux (φ) through it.

Quantitatively .

S.I. unit of magnetic flux is weber (Wb).

Biot-Savart law

Magnetic field due to a current Element

The magnetic field strength at point P due to a small length dl of the conductor carrying current I is given by :
is called the permeability of free space or vacuum.

Here r is the distance of point P from the current element under consideration and θ is the angle betweenand  where  is in the direction of I.

Thus, the direction of  is perpendicular to the plane containing and  .

a) Magnetic field due to a straight conductor carrying current

Magnetic field strength at a distance d from a straight conductor carrying current I is given by :

Direction of magnetic field is suggested by right hand grip/thumb rule. 

b) Magnetic field due to a circular coil

Magnetic field at a point on the axis of a coil, having N turns, radius of r, distance d from the centre of the coil is given by :
In general for any circular section as shown

Ampere’s circuital laws

The line integral of magnetic field  around any closed path in vacuum is  times the net current (I) threading through the area enclosed by the curve.

a) Magnetic Field due to a solenoid

A solenoid is a long, straight coil of several turns whose length is much larger than the diameter of each turn. 

Magnetic field at the centre of a solenoid having n turns per unit length and carrying a current I is given by : 
B = μ0nI The field strength is uniform at all points well inside the solenoid. The direction of magnetic field inside a solenoid carrying current can be found using right hand grip rule.

At the edges of a short solenoid.

where n is no. of turns per unit length.

b) Magnetic Field due to a toroid

A toroid is a solenoid in the form of a ring. Magnetic field inside the toroid is constant and is given by :
B= μ0nI
where n is no. of turns per unit length and I is the current flowing through it.

B) Motion of charged particles in electric and magnetic fields

1. A Charged Particle in a Uniform Electric Field.
2. A Charged Particle in a Uniform Magnetic Field.
3. Force on a Current Carrying Conductor in a Magnetic Field.
4. Force between two Parallel Current Carrying Conductors.
5. Magnetic Effect of Current – Definition of an Ampere.
6. Force Between Two Current Elements not parallel to each other.
7. Torque Experienced by a Current Loop in a Magnetic Field.
8. Potential Energy of a Current Loop in a Magnetic Field.
9. Moving Coil Galvanometer.
10. Sensitivity of a Galvanometer.
11. Conversion of a Galvanometer into a Voltmeter.
12. Conversion of a Galvanometer into an Ammeter.

A Charged Particle in a Uniform Electric Field

a)A charge at rest or moving parallel to an electric field either gets accelerated or retarded in a direction parallel to the electric field.

b)A charge moving perpendicular to an electric field describes a parabolic path. Equation of the parabolais given as :

where m is mass of the charged particle.
v is velocity of the particle in x-axis.
q is charge on particle.
y is the distance moved by the particle in a direction parallel to the electric field E.

c)Force experienced by a charge in an electric field is called electric Lorentz force. It is given by

A Charged Particle in a Uniform Magnetic Field

When
 the charged particle follows a circular path of radius
(a) As the force given by 
acts perpendicular to  , the force does no work on the charged particle and therefore the kinetic energy of the charged particle and therefore the kinetic energy of the charged particle remains unchanged.(b) If charge is accelerated by p .d V, then

(d) The period of revolution of charge q in a uniform magnetic field B is given by
It is independent of the radius of the circular path followed by the charged particle and is also independent of the speed of the charged particle .

Force on a Current Carrying Conductor in a Magnetic Field

Force between two Parallel Current Carrying Conductors

a)Two long parallel conductors carrying current in the same direction attract each other. For two long, parallel conductors kept a distance r apart in vacuum and carrying current I1 and I2 respectively, the force per unit length experienced by each of them is given by

b)The nature of force of interaction between the current carrying conductors can be explained on the basis of right hand grip rule and Flemings Left Hand Rule. These rules can be used to show that two long, parallel conductors carrying current in the opposite direction will repel each other.

Magnetic Effect of Current – Definition of an Ampere

When 1 ampere each is passing through two long, parallel conductors kept 1 m apart in vacuum, a force of magnitude 2×10-7 N is experienced by a meter length of each conductor.

This definition of an ampere follows from the formula for the force between two parallel current carrying conductors.

Force Between Two Current Elements not parallel to each other

Force experienced by 1st current element due to the second current element is

Torque Experienced by a Current Loop in a Magnetic Field

a)When rectangular loop having N turns of area A each is suspended in a uniform magnetic field B such that the normal to the plane of the loop makes an angle θ with the direction of the magnetic field B, the torque τ experienced by the loop is given by. Here I is the current in the loop. Here M = I(NA) is called the magnetic dipole moment of the current loop and is defined as the product of the current in the loop and the total area of the loop . The direction of magnetic dipole moment of a current loop is along the direction of the magnetic field due to the current in the loop. Thus, for the given direction of current in a loop, the direction of its dipole moment vector can be found using right hand grip rule. 

Potential Energy of a Current Loop in a Magnetic Field

When a current loop of magnetic dipole moment, M = INA is held in a uniform magnetic field B in such a way that the direction of the potential energy of the dipole is given as
 cos θ where the zero of potential energy corresponds to θ = 90°.
(a) when θ = 0°, U = - MB and is minimum moreever t = 0 for θ = 0.
So θ = 0° is the orientation or position of stable equilibrium of a current loop (or a magnetic dipole) in a uniform magnetic field.

(b) when θ = 180°, U = MB and is maximum though t = 0 for θ = 180° also.
So θ = 180° corresponds to the position or orientation of unstable equilibrium of a current loop or a magnetic dipole in uniform magnetic field.

Moving Coil Galvanometer

Galvanometer is an electromechanical instrument which is used for the detection of electric currents through electric circuits. Being a sensitive instrument, Galvanometer can not be used for the measurement of heavy

currents. However we can measure very small currents by using galvanometer but the primary purpose of galvanometer is the detection of electric current not the measurement of current.

WORKING PRINCIPLE

Galvanometer works on the principle of conversion of electrical energy into mechanical energy. When a current flows in a magnetic field it experiences a magnetic torque. If it is free to rotate under a controlling torque, it rotates through an angle proportional to the current flowing through it.

ESSENTIAL PARTS OF GALVANOMETER

There are five essential parts of a Galvanometer.

1. A U-shaped permanent magnet with concave poles.
2. Flat rectangular coil of thin enameled insulated wire ‘C’.
3. A soft iron cylinder ’B’.
4. A pointer or needle.
5. A scale.

CONSTRUCTION

The flat rectangular coil of thin enameled insulated wire of suitable number of turns wound on a light nonmetallic or aluminum frame is suspended between the cylindrically concave poles of magnet by a thin phosphor bronze strip. One end of the wire of the coil is soldered to strip. The other end of the strip fixed to the frame of the galvanometer and connected to an external terminal. It serves as one leas current lead through which the current enters or leaves the coil. The other end of the wire of the coil is soldered to a loose and soft spiral of wire connected to another external terminal. The soft spiral of a wire serves as the other current lead. A soft-iron cylinder, coaxial with the pole pieces, is placed within the frame of the coil and is fixed to the body of the galvanometer. In the space between it and the pole pieces, where the coil moves freely, the soft iron cylinder makes the magnetic field stronger and radial such that into whatever position the coil rotates, the magnetic field is always parallel to its plane.

WORKING When a current passes through the galvanometer coil, it experiences a magnetic deflecting torque, which tends to rotate it from its rest position. As the coil rotates it produces a twist in the suspension strip. The twist in the strip produces an electric restoring torque. The coil rotates until the elastic restoring torque due to the strip does not equal and cancels the deflecting magnetic torque, then it attains equilibrium and stops rotating any furthers.

Deflecting magnetic torque = BINA Cosα

where B = Strength of the magnetic field.

I = Current in the coil.
A = Area of the coil.
N = Number of turns in the coil.
α= The angle of deflection of the coil.
The restoring elastic torque is proportional to the angle of twist of the suspension strip According to Hook’s Law

Restoring torque = Cθ
Where θ = Angle of twist.
C = torque per unit twist. Under equilibrium condition :


If the magnetic field were uniform (as with flat pole pieces) α would continuously increase with θ and Cos α factor would not be constant. Then the current "I" would not be proportional to "θ" and the scale of the galvanometer not linear. However, due to the radial magnetic field the plane of the coil is always parallel to the field irrespective of the position of the coil rotates. So "α" the angle between the plane of the coil and direction of the field is always zero. Hence Cosα= I. The equation (i) therefore, reduces to: I = C θ/BAN Since C, B, A and N are constant for a galvanometer, therefore, Iαθ
Thus current through the coil is directly proportional to the angle of twist of the suspension (or deflection) θ.

Sensitivity of a Galvanometer

a) Current Sensitivity : It is defined as the coil deflection per unit current in it. 
b) Voltage Sensitivity : It is defined as the coil deflection per unit potential difference applied across its ends.

Conversion of a Galvanometer into a Voltmeter

A galvanometer of coil resistance G, showing full scale deflection for a current Ig can be converted into a voltmeter for measuring potential differences having values greater than  
by putting high resistance R in series with the galvanometer where: 

Conversion of a Galvanometer into an Ammeter

A galvanometer of coil resistance G, showing full scale deflection for a current Ig can be converted into an ammeter for measuring currents having values more than Ig(i.e., I>Ig) 
by putting a low resistance S in parallel with the galvanometer where: 
 
Here S is also known as the SHUNT RESISTANCE.

Thermal and Chemical Effects of Current

THERMAL AND CHEMICAL EFFECTS OF CURRENT


1. Heating Effects of Current
2. Chemical Effects of Current
3. Thermoelectric Effects of Current

Heating Effects of Current

1. Joule’s law of heating.
2. Cause of heating effect of current.
3. Electric power.
4. Electric energy.
5. Efficiency of an electric device. 

Joule’s law of heating

Joule’s laws are a pair of laws concerning the heat produced by a current and the energy dependence of an ideal gas to that of pressure, volume, and temperature, respectively.

Joule’s first law, also known as the Joule effect, is a physical law expressing the relationship between the heat generated by the current flowing through a conductor. It is named for James Prescott Joule who studied the phenomenon in the 1840s. It is expressed as:

Q = I2 RT Where Q is the heat generated by a constant current I flowing through a conductor of electrical resistance R, for a time t. When current, resistance and time are expressed in amperes, ohms, and seconds respectively, the unit of Q is the joule. Joule’s first law is sometimes called the Joule-Lenz law since it was later independently discovered by Heinrich Lenz. The heating effect of conductors carrying currents is known as Joule heating.

Joule’s first law is closely related to, and thus easily derived from Ohm’s Law. Below is a quick synopsis of how these two laws relate, for detailed information see Ohm’s Law.

Joule’s second law states that the internal energy of an ideal gas is independent of its volume and pressure, depending only its temperature.

Cause of heating effect of current

When we set up an electric field across the ends of a conductor, by applying a potential difference across it with the help of a source of e.m.f., free electrons present in the conductor get accelerated in a direction opposite to that of the electric field applied. These electrons get additional kinetic energy. These electrons suffer from frequent collisions with the ions or atoms of the lattice and transfer their gained kinetic energy to them. This increases average kinetic energy of vibration of the ions or atoms of the conductor. So the temperature of the conductor rises.This way electrical energy supplied by the source of e.m.f. gets converted into heat energy.

Electric power

Electric power is the rate at which energy is supplied by the source of e.m.f. in maintaining the current in an electric circuit.

The rate at which electric energy is consumed is called electric power.



Power is expressed in joule/second or watt.
When 1 ampere current is passed through a resistor of 1Ω, the heat energy produced is, 1 joule. If this flow is maintained for 1 second, the power consumed is 1 watt.

OR

Electrical power

It is the rate of production of electrical energy in a generator or the rate of consumption or dissipation of electrical energy in other forms of energy in appliances like electric motor, bulb, heater, etc. It is represented by the symbol P and is measured in watt (W) in the SI system of units.

Electric energy

Since there exists resistance to the flow of current, work has to be done in order to maintain the flow of current. Since potential difference V is the work done to carry unit positive charge from infinity to a point, the work done to carry a charge q is given by,



This also proves the Joule’s law of heating. Toasters, Irons and Electric stoves, Heat convectors use this energy. Tungsten filaments used in incandescent lamp operate at temperature of 2700°C

Both heat and light energy are evolved from this lamp.

Efficiency of an electric device

Chemical Effects of Current

1. Electrolyte and electrolysis.
2. Faraday’s laws of electrolysis.
3. Electrochemical Cells. 

Electrolyte and electrolysis

Electrolyte. A solution which dissociates into ions on passing current through it is called electrolyte and this is called electrolysis.

Faraday’s laws of electrolysis

Faraday’s 1st Law of Electrolysis:

The mass(m) of a substance produced at an electrode during electrolysis is directly proportional to the charge q passed through the electrolyte, i.e.,
maq
orm = Zq.
Here z is a constant called the electrochemical equivalent (E.C.E) and is different for different substances. Though its SI unit is kg C-1 it is expressed in g C-1 because it is very small. For example z of copper is 0.001118 g C-1. Charge q passed in the electrolyte can be determined from the steady current I and the time t for which it is passed in the electrolyte as
q = It
Thus m = zIt.
Where Z is called Electrochemical equivalent of the substance.

Faraday’s 2nd Law of Electrolysis:

The masses of different substances deposited or liberated by the passage of same electric charge are in the ratio of their chemical equivalents, i.e.,

where E1 , E2 are chemical equivalents of the two substances deposited in two electrolytes.
Here, the chemical equivalent, E of a substance is defined as the ratio of molar mass M of the substance and its valance p, i.e.,  

Faraday constant (F)

To deposite one mole m = M of a substance, charge required to flow is q = Npe

Where N is Avogadro’s number,
P is valence of the atome involved,
E is charge on an electron,
M is atomic mass of the substance to be deposited.

We know that m = Zq.
Here M = Znpe.
 

Faraday (F)

Charge required to deposit chemical equivalent of a substance is the same for all substances and is called a Faraday (F). Alternately, a Faraday is the charge of 1 mole of electrons. It is equal to 96500 C/gram-mole.In terms of F the electrochemical equivalent z and the chemical equivalent E r related as

Electrochemical Cells

An electrochemical cell is a device in which an e.m.f. is generated due to the chemical action. An electrochemical cell essentially consists of two electrodes of dissimilar metals or materials and an electrolyte.

Cells are of two types:

i) Primary Cells,
ii) Secondary Cells.

i) Primary Cells: In this type of cells, electrical energy is produced due to irreversible chemical reaction. Example of this type are Voltaic cell,Daniel cell, Leclanche cell,Dry cell, etc.

ii) Secondary Cells: In this type of cells, chemical reaction responsible for the production of electrical energy can be reversed. Thus,secondary cells can be charged again and again.Such cells are also known as storage cells or accumulators. Examples of this type of cells are lead-acid cell, Alkali cell, etc.

Voltaic Cell.

It is a primary electrochemical cell and has a standard e.m.f. of 1.08 V. Due to the defects of polarization and local action it cannot be used for long at a time.
Electrodes. Copper :Anode
Amalgamated Zn : Cathode

Electrolyte. Dil. H2SO4
Chemical reaction

e.m.f. of voltaic cell is about 1.08 V.

Defects of voltaic cell. There are two main defects :

i) Local action.
ii) Polarisation. 

Daniel Cell

E.m.f of a Daniel cell is 1.1 V which remains fairly constant for long time provided the current drawn from the cell is small.

Electrodes. Copper (container): Anode
Amalgamated Zn: Cathode
Electrolyte H2SO4 Daniel cell uses CuSO4 as depolariser .

Leclanche Cell

E.m.f. of a leclanche cell is 1.45 V. It cannot be used in situations demanding constant supply of current for long duration.

Electrodes. Carbon – Anode
Zinc – Cathode

Electrolyte NH4Cl.
A mixture of manganese dioxide and carbon powder is used around the carbon rod (anode). Manganese dioxide acts as depolariser and the carbon powder provides conductivity for flow of chage carriers.

 

Dry cell

Dry cell is portable form of Leclanche cell.

Ammonium chloride acts as an electrolyte. MnO2 acts as a depolariser. E.m.f. of the cell is 1.5 V.

Secondary Cell – Aklaki Accumulator (Ni-Fe) or Edison Cell.

Charging of Secondary cell

Here KOH is electrolyte

LiOH is to increase conductivity.
In solution ions present are

K+ and OH-
2KOH → 2K+ + 2OH-
charging Reaction at anode
Ni(OH)2+2(OH-) — 2e- → Ni(OH)4
Reaction at cathode
Fe(OH)2 + 2K+ + 2e- → Fe + 2KOH
(Spongy iron)
When full charged pot. diff. becomes 1.36 V.

Discharging

Reaction at anode
Ni(OH)4 + 2K+ + 2e- → Ni(OH)2 + 2KOH

Reaction at cathode
Fe + 2OH- — 2e- → Fe(OH)2

At 1.1 V, cell requires recharging.

Lead : Acid Cell

E.m.f. of lead (acid) cell is 2.05 V. As its internal resistance is low, it can be used for supplying large currents. When discharged, its e.m.f. falls to 1.8 V.Electrodes.
PbO2 - Anode
Pb - Cathod
Electrolyte. Dil H2SO4 of sp. gravity > 1.21.
A lead-acid cell needs recharging when the sp. gravity of H2SO4 falls to 1.12.

Thermoelectric Effects of Current

Thermoelectricity

It is direct conversion of heat into electrical energy, or the reverse. It encompasses Seebeck, Peltier and Thomson effects but, by convention, excludes other electro-thermal phenomena such as thermionic emission.

Thermocouple

A thermocouple is an arrangement of two dissimilar conductors (metals/alloys) connected end to end to form a close loop having two junctions.

Examples. Iron – copper thermocouple.
Antimony—Bishmuth thermocouple. 

Seebeck Effect

a) When the junctions of a thermocouple are maintained at different temperatures, an e.m.f. is generated in the thermocouple. This effect is known as Seebeck Effect. The e.m.f. generated is known as thermoelectric e.m.f. and depends on the temperature difference T of the two junctions as :
Here α and β are thermoelectric constant. Value of α and β is different for different pair of metals.

b) The thermoelectric e.m.f. generated in a thermocouple depends only on the temperature difference and not on the individual temperature of the two junctions. So if we keep one junction at 0°C and refer to this junction as the cold junction and increase temperature of the other junction called the hot junction, the thermoelectric e.m.f. varies with the temperature of the hot junction as shown in figure below.

For a certain temperature of the hot junction called neutral temperature Tn, the thermoelectric e.m.f. is maximum. When the temperature of the hot junction further increases, the thermoelectric e.m.f. decreases and becomes zero.

The temperature of the hot junction for which the thermoelectric e.m.f. becomes zero, is called the temperature of inversion Ti .

In terms of thermoelectric constants
α and β, Tn and Ti are
From this it follows that
i) Since α and β are different for different thermocouples, Tn and Ti are also different for different thermocouples .
 

Peltier Effect

a) When electric current is passed in a thermocouple, heat is evolved at one junction and absorbed at the other junction. This is known as Peltier Effect. The junction at which heat is evolved becomes hot and the other junction at which heat is absorbed becomes cold. 

b) For a given thermocouple, the amount of heat evolved or absorbed at a junction is directly proportional to the current through the juncton. 

Thomson Effect

The Thomson effect was predicted and subsequently experimentally observed by William Thomson (Lord Kelvin) in 1851. It describes the heating or cooling of a current-carrying conductor with a temperature gradient.Any current-carrying conductor (except for a superconductor), with a temperature difference between two points, will either absorb or emit heat, depending on the material.If a current density J is passed through a homogeneous conductor, heat production per unit volume; 

where ρ is the resistivity of the material
dT/dx is the temperature gradient along the wire
μ is the Thomson coefficient. 
The first term ρJ² is simply the Joule heating, which is not reversible .
The second term is the Thomson heat, which changes sign when J changes direction. 
Thomson effect is of two types : 

i) Positive Thomson effect. 
ii) Negative Thomson effect. 

Positive Thomson effect

In metals such as zinc and copper, which have a hotter end at a higher potential and a cooler end at a lower potential, when current moves from the hotter end to the colder end, it is moving from a high to a low potential, so there is an evolution of heat. This is called the positive Thomson effect.

Negative Thomson effect

In metals such as cobalt, nickel, and iron, which have a cooler end at a higher potential and a hotter end at a lower potential, when current moves from the hotter end to the colder end, it is moving from a low to a high potential, there is an absorption of heat. This is called the negative Thomson effect.

Thermoelectric Power

The rate of change of thermoelectric e.m.f. with temperature, 
is called thermoelectric power and is denoted by P .